OSC In CHOP
The OSC In CHOP is used to accept Open Sound Control Messages. OSC In can be used to accept messages from either a 3rd party application which adheres to the Open Sound Control specification (http://www.cnmat.berkeley.edu/OpenSoundControl/). OSC In is based on a connection-less system, meaning that it can accept multiple messages for any number of sources at the same time. The user must specify a port number which OSC In will look for incoming messages. This port must not have anything running on it before OSC In attempts to use it. OSC CHOPs in TouchDesigner use the UDP transport protocol.
There are options which allow the user to adjust the default message queuing system to optimize it for their specific network conditions and usage needs. The Min/Max Target size specifies a range which the queue attempts to keep the buffer size at in seconds. Increasing the Queue Adjust Time will determine how long the queue can be outside that range before it tries to correct it.
If the user wishes to use OSC In to detect when messages are arriving, there is a Pulse Mode toggle which will read a single sample of any incoming message when it arrives and displays the pulse reset values any other time. This is useful for syncing beats between TouchDesigner and another applications.
NOTE for Windows OS - If experiencing connection issues make sure Windows Firewall is disabled.
Parameters - OSC In Page
protocol - ⊞ - The network protocol to use. Refer to the Network Protocols article for more information.
- Messaging (UDP)
- Multi-Cast Messaging (UDP)
- Reliable Messaging (UDT Library)
netaddress - When using Multicast, this is the address that OSC In will listen for packets on.
port - The port which OSC-In will accept packets on.
active - While on, the CHOP receives information sent to the network port. While Off, no updating occurs. Data sent to the port is lost.
OSC Address Scope
oscaddressscope - To reduce which channels are generated, you can use channel name patterns to include or exclude channels. For example,
^*accel* will exclude accelerometer channels coming in from an iPhone or iOS app like mrmr. See Pattern Matching for the syntax of the possible channel name patterns.
Use Global Rate
useglobalrate - When on, the CHOP will sample at the global sample rate specified by TouchDesigner.
Default Sample Rate
samplerate - When Use Global Rate is off, this parameter is used to determine the sample rate of this CHOP.
mintarget - The smallest amount of queue data (represented in seconds) allowed without adjusting sampling speed.
Minimum Target Unit
maxtarget - The largest amount of queue data (represented in seconds) allowed without adjusting sampling speed.
Maximum Target Unit
maxqueue - The maximum allowed size of the queue (represented in seconds). If the maximum queue size is exceeded, data will be removed from the front of the queue.
Maximum Queue Unit
Queue Adjust Time
adjusttime - The maximum amount of time allowed for a queue to be above or below the maximum or minimum target without adjusting the sampling speed.
Queue Adjust Time Unit
Strip Prefix Segments
Keep Full Name
reset - Deletes all known channels and clears the queue.
Parameters - Common Page
timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match
srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such has
autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
|• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •|
To pulse a parameter is to send it a signal from a CHOP or python or a mouse click that causes a new action to occur immediately. A pulse via python is via the
.pulse() function on a pulse-type parameter, such as Reset in a Speed CHOP. A pulse from a CHOP is typically a 0 to 1 to 0 signal in a channel.
A parameter in most CHOPs that restricts which channels of that CHOP will be affected. Normally all channels of a CHOP are affected by the operator.
samples-per-second of a CHOP. Each CHOP in your network has a sample rate, whether it is used or not. The overall timeline has a "frame rate", which is the number of animation frames per second, generally your monitor display frequency.
A Time Slice is the time from the last cook frame to the current cook frame. In CHOPs it is the set of short channels that only contain the CHOP channels' samples between the last and the current cook frame.
Exporting is the connection of CHOP channels to parameters of operators. The output of each exporting CHOP is one or more channels, active only while the CHOP Viewer is on. The current value of a channel can be exported to a parameter of any operator, overriding that parameter's value. See Parameter.
Parameters in TouchDesigner are an operator's settings (numbers, menus, flags, strings, paths) which the user can alter. Parameters for any operator can be opened by right-clicking on the operator and selecting "Parameters..." A currently selected operator's parameters can be viewed in a Network Editor by pressing the keyboard shortcut 'p'.