The Gesture CHOP records a short segment of the first input and loops this segment in time with options as specified in the Gesture Page. The second input defines the "listen" input. The third input is used to reset the gesture.
gestureCapture component in the palette is much more powerful and flexible to capture and record channels, and has full UI.
In the Gesture CHOP, when the first channel of the listen input goes above zero, the Gesture CHOP begins recording the first input's channels. While listen is on, the input channels are output exactly as is. When the listen is turned off, the recorded segment of the channels is processed (trimmed and blended). While listen is off, the recorded segment is looped continuously.
The Gesture CHOP determines the number of beats that the listen was on for; this defines the period of the loop. If the beat frequency changes, the period will change with it.
If "Fit to Nearest Cycle" is Off, the beats are ignored and the gesture length is exactly the time it took to record - the recorded segment will be looped back with a period equal to the recorded length. When On, the captured gesture will be extended or trimmed to be a multiple of the beats per cycle.
Parameters - Gesture Page
playmode - ⊞ - Controls the gesture playback.
- Locked to Timeline
locked- This mode locks the gesture position to the Timeline.
sequential- This mode continually plays the gesture regardless of the timeline position. Reset and Reset Condition parameters below are enabled to allow some control.
Fit to Nearest Cycle
fitmethod - When on the captured gesture will be extended or trimmed to be a multiple of the Beats Per Cycle.
Beats per Cycle
numbeats - Specifies the number of beats to cycle the recorded animation around. If the recorded animation is longer than a multiple of the Beats Per Cycle, it will loop at that multiplied length.
step - If on, the cycled animation will increase in value each cycle length. Useful if you want to cycle animation but at the same time have the cycle drifting off of it original values.
stepreset - When On and you re-record a gesture, the step will be zeroed.
blend - How much of the recorded segment to use as a blend region. The blend region is used to blend the beginning of the segment to the end so that a seemless loop is produced.
Blend Time Unit
interp - If on, recorded samples are interpolated when scaling occurs, otherwise the nearest sample is selected.
speed - Scales the rate of playback for the segment.
resetcondition - ⊞ - This menu determines how the Reset input (the third input) triggers a reset of the channel(s).
- Off to On
offtoon- Channels are reset when the Reset input goes off to on.
- While On
on- Channels are reset when the Reset input goes on. The channel will hold the reset value until the input turns off.
- On to Off
ontooff- Channels are reset when the Reset input goes on to off.
- While Off
off- Channels are reset when the Reset input goes off. The channel will hold the reset value until the input turns on.
reset - Resets the gesture in Sequential Play Mode.
Parameters - Common Page
timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match
srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such has
autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
- Input 0 -
- Input 1 -
- Input 2 -
|• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •|
The panel at the bottom of TouchDesigner, it controls the current Time of the full system or just one component.
To pulse a parameter is to send it a signal from a CHOP or python or a mouse click that causes a new action to occur immediately. A pulse via python is via the
.pulse() function on a pulse-type parameter, such as Reset in a Speed CHOP. A pulse from a CHOP is typically a 0 to 1 to 0 signal in a channel.
A Time Slice is the time from the last cook frame to the current cook frame. In CHOPs it is the set of short channels that only contain the CHOP channels' samples between the last and the current cook frame.
A parameter in most CHOPs that restricts which channels of that CHOP will be affected. Normally all channels of a CHOP are affected by the operator.
samples-per-second of a CHOP. Each CHOP in your network has a sample rate, whether it is used or not. The overall timeline has a "frame rate", which is the number of animation frames per second, generally your monitor display frequency.
Exporting is the connection of CHOP channels to parameters of operators. The output of each exporting CHOP is one or more channels, active only while the CHOP Viewer is on. The current value of a channel can be exported to a parameter of any operator, overriding that parameter's value. See Parameter.
Parameters in TouchDesigner are an operator's settings (numbers, menus, flags, strings, paths) which the user can alter. Parameters for any operator can be opened by right-clicking on the operator and selecting "Parameters..." A currently selected operator's parameters can be viewed in a Network Editor by pressing the keyboard shortcut 'p'.