Difference between revisions of "Beat Dialog"

From TouchDesigner Documentation
Jump to: navigation, search
m
m
Line 7: Line 7:
 
Set '''Beat Input''' is set to '''Listen/Tap'''.
 
Set '''Beat Input''' is set to '''Listen/Tap'''.
  
To set the BPM, first turn on the Listen button.  Then press the Tap button '''EVERY 4 BEATS''', preferably at the beginning of each bar. After 10 or 20 seconds, stop pressing the Tab button, and turn off the Listen button.  You can see teh BPM has changed, and it will heep that bpm until you change it again.
+
To set the BPM, first turn on the Listen button.  Then press the Tap button '''EVERY 4 BEATS''', preferably at the beginning of each bar. The BPM adjusts every time you tap. After 10 or 20 seconds, stop pressing the Tab button, and turn off the Listen button.  You can see the BPM has changed, and it will keep that BPM until you change it again.
  
 
The Beat Panel will average out your taps to the closest BPM, so you can keep tapping EVERY 4th BEAT to get a more accurate average BPM.
 
The Beat Panel will average out your taps to the closest BPM, so you can keep tapping EVERY 4th BEAT to get a more accurate average BPM.
  
After it drifts, you can resync the beginning of a ramp cycle to the start of a bar of music: With the Listen button off, press the Tap button once. It will re-sync.
+
After the cycles drifts from the music, you can resync the beginning of a ramp cycle to the start of a bar of music: With the Listen button off, press the Tap button once. It will re-sync, and not affect the BPM.
 
 
The orange triangle on the beat circle lets you adjust the phase up to one cycle in case you want to advance/retard your visual relative to the music.
 
 
 
  
 +
The orange triangle on the beat circle lets you adjust the phase in case you want to advance/retard your visual relative to the music.
  
 
You can watch the beat cycle, or use the [[Beat CHOP]] to generate 0-to-1 ramps based on the beats-per-minute.
 
You can watch the beat cycle, or use the [[Beat CHOP]] to generate 0-to-1 ramps based on the beats-per-minute.

Revision as of 22:30, 22 July 2019

The Beat dialog under the Dialogs menu lets you set the beats-per-minute (BPM) of a TouchDesigner project by letting you tap in the beat while you are listening to music. It is used by the Beat CHOP to determine the length of its cycles and its "phase" (when it returns to the start of a loop).

BeatDialog1.png

How to set BPM and Phase in Listen/Tap Mode

Set Beat Input is set to Listen/Tap.

To set the BPM, first turn on the Listen button. Then press the Tap button EVERY 4 BEATS, preferably at the beginning of each bar. The BPM adjusts every time you tap. After 10 or 20 seconds, stop pressing the Tab button, and turn off the Listen button. You can see the BPM has changed, and it will keep that BPM until you change it again.

The Beat Panel will average out your taps to the closest BPM, so you can keep tapping EVERY 4th BEAT to get a more accurate average BPM.

After the cycles drifts from the music, you can resync the beginning of a ramp cycle to the start of a bar of music: With the Listen button off, press the Tap button once. It will re-sync, and not affect the BPM.

The orange triangle on the beat circle lets you adjust the phase in case you want to advance/retard your visual relative to the music.

You can watch the beat cycle, or use the Beat CHOP to generate 0-to-1 ramps based on the beats-per-minute.

See Also: Beat CHOP.