MoSys CHOP

Summary

NOTE

License: Only available in TouchDesigner Pro.

The MoSys CHOP receives data from a MoSys camera tracking system. The channels can be used to control a virtual camera and to implement lens distortion via the MoSys TOP as part of a virtual production system.

mosysCHOP_Class

Parameters - MoSys Page

Active active - While on, the CHOP receives information sent to the network port. While Off, no updating occurs. Data sent to the port is lost.

Protocol protocol - ⊞ - The network protocol to use. Refer to the Network Protocols article for more information.

• Messaging (UDP) msging -

• Multi-Cast Messaging (UDP) multicastmsging -

Network Address netaddress - When using Multicast, this is the address that to listen for packets on.

Network Port port - The port which MoSys CHOP will accept packets on.

Local Address localaddress - Specify an IP address to receive on, useful when the system has mulitple NICs (Network Interface Card) and you want to select which one to use.

Camera ID cameraid - Used to filter out unwanted data packets when more than one camera is sending data to this machine. This parameter should be a number that matches the value in the camera id channel. Data received from cameras that do not match this id will be ignored. If this field is blank, the most recent data received each frame will be displayed regardless of what camera it comes from.

Screen Width screenwidth - The width of the camera image in pixels. It is used to convert the focal distance received by the camera into a FOV value.

Parameters - Common Page

Time Slice timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.

Scope scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.

Sample Rate Match srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.

• Resample At First Input's Rate first - Use rate of first input to resample others.

• Resample At Maximum Rate max - Resample to the highest sample rate.

• Resample At Minimum Rate min - Resample to the lowest sample rate.

• Error If Rates Differ err - Doesn't accept conflicting sample rates.

Export Method exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.

• DAT Table by Index datindex - Uses the docked DAT table and references the channel via the index of the channel in the CHOP.

• DAT Table by Name datname - Uses the docked DAT table and references the channel via the name of the channel in the CHOP.

• Channel Name is Path:Parameter autoname - The channel is the full destination of where to export to, such has geo1/transform1:tx.

Export Root autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.

Export Table exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).

Info CHOP Channels

Extra Information for the can be accessed via an Info CHOP. Info Channels Common Page

Common Operator Info Channels

• total_cooks - Number of times the operator has cooked since the process started.

• cook_time - Duration of the last cook in milliseconds.

• cook_frame - Frame number when this operator was last cooked relative to the component timeline.

• cook_abs_frame - Frame number when this operator was last cooked relative to the absolute time.

• cook_start_time - Time in milliseconds at which the operator started cooking in the frame it was cooked.

• cook_end_time - Time in milliseconds at which the operator finished cooking in the frame it was cooked.

• cooked_this_frame - 1 if operator was cooked this frame.

• warnings - Number of warnings in this operator if any.

• errors - Number of errors in this operator if any.

TouchDesigner Build: Latest\nwikieditor2023.11280before 2023.11280

An Operator Family which operate on Channels (a sequence of numbers (Samples)) which are used for animation, audio, mathematics, simulation, logic, UI construction, and data streamed from/to devices and protocols.

A Time Slice is the time from the last cook frame to the current cook frame. In CHOPs it is the set of short channels that contain the CHOP channels' samples between the last and the current cook frame.

A parameter in most CHOPs that restricts which channels of that CHOP will be affected. Normally all channels of a CHOP are affected by the operator. TOPs have Channel Mask, a similar feature.

samples-per-second of a CHOP. Each CHOP in your network has a sample rate. In contrast, the overall timeline has a Frame Rate, which is the number of frames to cook and display per second, generally your monitor display frequency, default 60.

Exporting is the connection of CHOP channels to parameters of operators. The output of each exporting CHOP is one or more channels, active only while the CHOP Viewer is on. The current value of a channel can be exported to a parameter of any operator, overriding that parameter's value. See Parameter.

An Operator Family that manipulates text strings: multi-line text or tables. Multi-line text is often a python Script or GLSL Shader, but can be any multi-line text. Tables are rows and columns of cells, each containing a text string.

The location of an operator within the TouchDesigner environment, for example, /geo1/circle1, a node called circle1 in a component called geo1. The path / is called Root. This path is displayed at the top of every Pane, showing which Component's network you are currently in. To refer instead to a filesystem folder, directory, disk file or http: address, see Folder.

Every operator in TouchDesigner has a set of control Parameters that can be integer or floating point numbers, menus, binary toggles, text strings or operator paths, which determine the output of the operator.

TouchDesigner is a hierarchy of components. "root" is the top-most network in the hierarchy. The Network Path or Path for root is simply /. A typical path is /project1/moviein1.