Keyboard In DAT
The Keyboard In DAT lists the most recent key events in its FIFO (first in/first out) table. There is one row for every key press down and every key-up, including Shift, Ctrl and Alt, with distinction between left and right side. For convenience, with each key press, a column indicates if the Shift, Ctrl and Alt were being held down at the time.
You get key presses even of the cursor is outside the TouchDesigner windows, whether they are control panels, Perform Mode or the network editor window. Exceptions: while entering text in the editor window.
You can set a filter to watch only certain keys. Custom shortcuts can be defined and handled by a python callback in the attached script.
Parameters - Keyboard In Page
active - Inhibits and allows message to be added to log.
Perform Window Only
perform - When on, key events are only detected while in perform mode.
keys - List of keys to allow through the filter. Just put the characters in the list, space-separated. Eg. '1 2 g h' for the 1, 2, g and h keys. Only these keys will be added to the log and generate an event. If blank, no filtering will be done. List of accepted keys: Keyboard UI
shortcuts - List of shortcuts to watch for. See "Shortcuts" in the notes for defining shortcuts.
panels - Optional list of references to panels to detect events from. Events will only be fired when any of the listed panels has focus.
lrmodifiers - When on, the states of the left and right modifier keys (see Notes) will be added to the table. Switching the state of this parameter will reset the table's contents.
Parameters - Log Page
executeloc - ⊞ - Determines the location the script is run from.
- Current Node
current- The script is executed from the current node location (for example, where 'cc' points to).
- Callbacks DAT
- Specified Operator
op- The script is executed from the operator specified in the From Operator parameter below.
fromop - The operator whose state change will trigger the DAT to execute its script when Execute is set to Specified Operator. This operator is also the path that the script will be executed from if the Execute From parameter is set to Specified Operator.
clamp - The DAT is limited to 100 messages by default but with Clamp Output, this can be set to anything including unlimited.
maxlines - Limits the number of messages, older messages are removed from the list first.
clear - Deletes all lines except the heading. To clear with a python script
Parameters - Common Page
language - ⊞ - Select how the DAT decides which script language to operate on.
input- The DAT uses the inputs script language.
node- The DAT uses it's own script language.
extension - ⊞ - Select the file extension this DAT should expose to external editors.
dat- various common file extensions.
- From Language
language- pick extension from DATs script language.
- Custom Extension
custom- Specify a custom extension.
customext - Specifiy the custom extension.
wordwrap - ⊞ - Enable Word Wrap for Node Display.
input- The DAT uses the inputs setting.
on- Turn on Word Wrap.
off- Turn off Word Wrap.
Shortcuts are defined by a list of modifier keys (see below) and a "trigger" key separated by .'s.
ctrl.shift.a the modifier keys are ctrl and shift, and the trigger key is a. This shortcut will be activated when one of the ctrl and shift keys are pressed and the trigger key, a is pressed down. If any other modifier keys are pressed, the shortcut will not be detected.
Modifier Keys - The following are all the valid modifier keys:
lalt- Left alt key.
ralt- Right alt key.
alt- Either left or right alt key.
lctrl- Left ctrl key.
rctrl- Right ctrl key.
ctrl- Either left or right ctrl key.
lshift- Left shift key.
rshift- Right shift key.
shift- Either left or right shift key.
|• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •|
An that manipulates text strings: multi-line text or tables. Multi-line text is often a command , but can be any multi-line text. are rows and columns of cells, each containing a text string.
Mode where the network editing window is not open, your performance interface window(s) is open and you are running your application as fast as possible. See .
Strictly refers to a window in Microsoft Windows. User-created windows are made with inside , aside from the TouchDesigner editor window and its dialogs.
The generic thing that holds an , and includes (display, bypass, lock, render, immune) and its position/size in the network. Whether you "lay down an Operator" or "lay down an Node", you're doing the same thing.
Any of the procedural data operators. OPs do all the work in TouchDesigner. They "cook" and output data to other OPs, which ultimately result in new images, data and audio being generated. See .