Experimental:Audio File Out CHOP
Summary[edit]
The Audio File Out CHOP saves an audio stream out to a file using a variety of different codecs.
Currently supports .wav, .mp3, .aiff, and .ogg container formats.
See also: Movie File Out TOP.
Parameters - Audio File Out Page
File Type filetype - ⊞ - Select the file type (container) of the output file.
- WAV
wav- .wav file type. The audio codec can be chosen using the Codec parameter.
- OGG
ogg- .ogg file type. The audio codec is Vorbis. Vorbis compression will have gapless playback.
- MP3
mp3- .mp3 file type. The audio codec is MP3. MP3 compression will not have gapless playback. Vorbis (.ogg) is a good alternative for this.
- AIFF
aiff- .aiff file type. The audio codec is Uncompressed 16-bit (PCM).
Unique Suffix uniquesuff - When enabled, me.fileSuffix will be a unique suffix when used in the file parameter.
N n - When unique suffix is disabled, me.fileSuffix will simply contain the value of N, instead of being unique
File file - Sets the path and filename of the audio file that is saved out. The file extension must match the file type parameter.
Codec codec - ⊞ - Select the compression codec for the WAV file type.
- Uncompressed 16-bit (PCM)
pcm16- Uncompressed audio (Pulse Code Modulation)
- Uncompressed 24-bit (PCM)
pcm24- Uncompressed audio (Pulse Code Modulation)
- Uncompressed 32-bit (PCM)
pcm32- Uncompressed audio (Pulse Code Modulation)
Bit Rate bitrate - ⊞ - Selects the bit rate for the MP3 file type.
- 96 kb/s
b96-
- 128 kb/s
b128-
- 192 kb/s
b192-
- 256 kb/s
b256-
- 320 kb/s
b320-
Record record - When toggled on, it will open the audio file and begin recording. When toggled off, it will close the file and release the read/write lock.
Pause pause - Pauses the recording of the audio to the audio file.
Parameters - Common Page
Time Slice timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
Scope scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first- Use rate of first input to resample others.
- Resample At Maximum Rate
max- Resample to the highest sample rate.
- Resample At Minimum Rate
min- Resample to the lowest sample rate.
- Error If Rates Differ
err- Doesn't accept conflicting sample rates.
Export Method exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname- The channel is the full destination of where to export to, such hasgeo1/transform1:tx.
Export Root autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
Export Table exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).
| CHOPs |
|---|
| • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • |
An Operator Family which operate on Channels (a series of numbers) which are used for animation, audio, mathematics, simulation, logic, UI construction, and many other applications.
To pulse a parameter is to send it a signal from a CHOP or python or a mouse click that causes a new action to occur immediately. A pulse via python is via the .pulse() function on a pulse-type parameter, such as Reset in a Speed CHOP. A pulse from a CHOP is typically a 0 to 1 to 0 signal in a channel.
A Time Slice is the time from the last cook frame to the current cook frame. In CHOPs it is the set of short channels that only contain the CHOP channels' samples between the last and the current cook frame.
A parameter in most CHOPs that restricts which channels of that CHOP will be affected. Normally all channels of a CHOP are affected by the operator.
samples-per-second of a CHOP. Each CHOP in your network has a sample rate, whether it is used or not. The overall timeline has a "frame rate", which is the number of animation frames per second, generally your monitor display frequency.
Exporting is the connection of CHOP channels to parameters of operators. The output of each exporting CHOP is one or more channels, active only while the CHOP Viewer is on. The current value of a channel can be exported to a parameter of any operator, overriding that parameter's value. See Parameter.
An Operator Family that manipulates text strings: multi-line text or tables. Multi-line text is often a command Script, but can be any multi-line text. Tables are rows and columns of cells, each containing a text string.
Parameters in TouchDesigner are an operator's settings (numbers, menus, flags, strings, paths) which the user can alter. Parameters for any operator can be opened by right-clicking on the operator and selecting "Parameters..." A currently selected operator's parameters can be viewed in a Network Editor by pressing the keyboard shortcut 'p'.
TouchDesigner is a hierarchy of components. "root" is the top-most network in the hierarchy. The Path is simply /. A typical path is /project1/moviein1.
